Aruba 387 Access Point
HPE 387 Access Point 802.11ad and 802.11ac for high speed outdoor point-to-point connectivity
These high-performing access points are a reliable, simple to deploy, point-to-point solution built to endure extreme temperature and moisture.
Weather-proof and temperature-hardened, the 387 Series APs withstand the harshest outdoor environments.
The 387 Series APs deliver gigabit per second aggregate throughput at distances up to 400 meters (or 0.25 miles).
High-speed, outdoor, point-to-point connectivity
With a maximum concurrent on the air data rate of 2.5 Gbps in the 60GHz band and 867 Mbps in the 5GHz band, the 387 Series delivers an aggregate peak data rate of 3.37 Gbps.
Flexible, intelligent radio offering
The 387 Series access points include dual radio supports for 60GHz and 5GHz to provide throughput in good conditions and provide intelligent fallback if the 60GHz radio is impacted by heavy rainfall.
The 387 Series APs help protect user authentication, wireless traffic, and data, with support for WPA and Enhanced Open, WPA-MPSK, and VPN tunnels.
Weatherproof and temperature-hardened
Supporting temperatures from -40°C to +60°C (-40°F to +140°F) and IP66/67 rated, the 387 Series can withstand the harshest environments.
HPE 387 Access Point Specifications
AP type :
- Temperature-hardened, dual radio, 60GHz 11ad and 5GHz 802.11ac 2×2 MIMO
60 GHz 802.11ad 1×1 (2502.5 Mbps max rate) radio
- 1 Spatial Stream for up to 2.5 Gbps
- Internal scanning antenna
- +/- 45° Azimuth Scan
- +/- 17° Vertical Scan
5GHz 802.11ac 2×2 MU-MIMO (867 Mbps max rate)
- Two spatial stream MIMO for up to 867 Mbps wireless data
- Internal directional antenna 9 dBi
Software-configurable dual radio supports 5 GHz (Radio 0) and 60GHz (Radio 1)
Supported frequency bands (country-specific restrictions apply) :
- 2.400 to 2.4835 GHz (BLE)
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz
- 5.825 to 5.875 GHz
- 57 to 64 GHz
Available channels: Dependent on configured regulatory domain
Dynamic frequency selection (DFS) maximizes the use of available 5GHz RF spectrum.
HPE 387 Access Point Supported radio technologies :
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
- 802.11ad: Single carrier (SC)
Supported modulation types :
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
- 802.11ad: BPSK, QPSK
Transmit power: Configurable in increments of 0.5 dBm for 5 GHz
Maximum EIRP (limited by local regulatory requirements):
- 60GHz band: 40 dBm EIRP max
- 5GHz band: 387: 34 dBm EIRP
Maximum ratio combining (MRC) for improved receiver performance on 5 GHz
Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
Short guard interval for 20MHz, 40MHz, 80MHz on 5GHz
Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
802.11ac Transmit beam-forming (TxBF) for increased signal reliability and range
802.11ad Beam Steering
HPE 387 Access Point Supported 11a/ac data rates (Mbps) :
- 802.11a 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n (5GHz): 6.5 to 600 (MCS0 to MCS15)
- 802.11ac: 6.5 to 867 Mbps (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80)
802.11n high-throughput (HT) support: HT 20/40
802.11ac very high throughput (VHT) support: VHT 20/40/80/160
802.11n/ac packet aggregation: A-MPDU, A-MSDU